INSTALLATION INSTRUCTIONSAND USER MANUALRESIDENTIAL USE ONLYINSTALLER: LEAVE THIS MANUAL WITH THE HOMEOWNER.HOMEOWNER: USE AND CARE INFORMATION ON PAG
7. Turn the unit switch knob to OFF position in order to unlock the door. Unlatch the door and open it. If required, the door can be removed. To do so
5.2 HOW TO HANG THE UNITUse the 4 chains and springs in the hardware pack provided with the unit. According to your needs, you can install the unit ei
- 12 -5.3 PLANNING OF THE DUCTWORKAll units in this manual are prebalanced.• Keep it simple. Plan for a minimum of bends and joints. • Keep the length
5.4 INSTALLING NON-INSULATED DUCTS AND REGISTERS (CONT’D)5.4.1 STAND ALONE SYSTEM (AS ILLUSTRATED IN SECTION 1.1.1) (CONT’D)ALL UNITSHow to connect t
5.4 INSTALLING NON-INSULATED DUCTS AND REGISTERS (CONT’D)5.4.2 CENTRAL DRAW POINT (AS ILLUSTRATED IN SECTION 1.1.2) (CONT’D)Fresh/Filtered air ductwo
5.5 INSTALLING INSULATED FLEXIBLE DUCTSUse the following procedure for connecting the insulated flexible ducts to the Tandem® transition* (EXHAUST AIR
5.5 INSTALLING INSULATED FLEXIBLE DUCTS (CONT’D)5.5.2 CONNECTION TO THE 5’’ TO 6’’ OVAL PORTS OF THE UNIT (CONT’D)4. Apply duct tape gently to the jo
5.6 INSTALLING DUAL EXTERIOR HOOD (CONT’D)5.6.3 CONNECTING TANDEM® TRANSITION TO EXTERIOR DUAL HOOD (CONT’D)2. Join the end of the Tandem transition
6.1 MAIN SWITCHAll units are equipped with a 3-position main switch, located on the front panel. 6.2 40415 AND 40425 WALL CONTROLS DESCRIPTIONThe incl
6.4 WALL CONTROLS CONFIGURATIONSee the configuration table below for the list of configuration parameters. Press the Menu button for 3 seconds to ente
ABOUT THIS MANUALFirst, we want to congratulate you on your purchase of this excellent unit which will allow you and your family to enjoy clean and he
- 20 -7. MAINTENANCEWARNINGRisk of electrical shocks. Before performing any maintenance or servicing, always disconnect the unit from its power source
- 21 -7.1 BIANNUAL MAINTENANCE (ESSENTIAL) (CONT’D)6. Wash the 2 core filters under hot water with mild soap. Rinse thoroughly and let dry completely
If the problem is still not solved, call your installer or the nearest authorized Service Center. Also, you can reach the Customer Service Department
1. TYPICAL INSTALLATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-61.1 HR
1. TYPICAL INSTALLATIONSInstallations may vary according to the model number and the position in which the unit is installed. Use the following illust
1. TYPICAL INSTALLATIONS (CONT’D)
All 3 types of installations can be used in the attic (Stand Alone, Central Draw Point or Return-Return). The example shown below is aReturn-Return in
- 7 -2.3 MOUNTING AND SERVICING CONSIDERATIONS• The two following pictures are showing the minimum clearance needed to open the door completely. 22.5”
- 8 -3.3 LOCATING THE UNITChoose an appropriate location for the unit.• Within an area of the house where the ambient temperature is between 10°C (50°
- 9 -1. Route the cable from the unit to a convenient location for the wall control. 2. Loosen the locking screw (the screw cannot be completely remov
Commentaires sur ces manuels